HMEC 46BedienungsanleitungInstructions for useNotice d’emploiIstruzioni per l’usoInstrucciones para el usoGebruiksaanwijzingBook_51xxxx_1106_SP6.book
8The operating controls of the HMEC 46Operating control I Volume controls LED NoiseGard™ ON/OFF switch Mono/stereo switch BOOM switch L/R 3.5 mm
9Operating control II LED NoiseGard™ ON/OFF switchHeadset with operating control IIOperating elementHMEC 46-CP x xHMEC 46-KP x xHMEC 46-NP x
10Using the headsetSwitching NoiseGard™ on/offThe NoiseGard™ ON/OFF switch allows you to switchthe NoiseGard™ active noise compensation on or off. W
11Switching between mono and stereo modeThe mono/stereo switch allows you to switch betweenmono () and stereo () mode, depending on theintercom s
12The operating time with batteries/rechargeable batteriesis approx. 100 hours.With NoiseGard™ switched on (see page 10), the LED provides informatio
13Connecting a mobile telephoneThe 2.5 mm jack socket allows you to connect a mobiletelephone. For this purpose, the NoiseGard™ active noisecompensa
14Connecting an additional audio playerThe 3.5 mm jack socket allows you to connect andlisten to an audio player (not supplied) through theheadset.
15Care and maintenanceCleaning the headsetUse a soft, slightly damp cloth to clean the headset fromtime to time. If the headset is very dirty, use a c
16Accessories and spare partsBy changing the cables, you can simply retrofit differentoperating controls (see “The operating controls of theHMEC 46” o
17Product variants Single-sided round cable, length 1.85 m XLR-5 connector ¼“ (6.3 mm) jack plug (headphones) PJ-068 equivalent (microphone) 8-pi
Book_51xxxx_1106_SP6.book Seite 2 Mittwoch, 13. Juni 2007 3:07 15
18SpecificationsHeadphonesTransducer principle dynamic, openEar coupling supra-auralFrequency response 20–14,000 HzImpedance 600 Ω / 1.200 Ωmono/stere
19General dataTemperature range Operation: –15 °C to +55 °CStorage: –55 °C to +70 °CWeight without cable approx. 150 gPower supply for 2x 1.5 V AA
20Connector assignmentHMEC 46-CP, -V-CP, -B-CP, -BV-CPHMEC 46-NPHMEC 46-V-RPSolder side123Audio Hi Audio Lo / DC–Microphone Hi4512345Microphone LoPow
21HMEC 46-KP, -V-KP, -B-K, -BV-KHMEC 46-KP1 Audio Hi left 1 Power supply NoiseGard™ (DC+)2 not assigned 2 Microphone Hi3 Audio Lo / DC– 3 Microphone L
22Manufacturer DeclarationsWarranty regulationsThe guarantee period for this Sennheiser product is 60 months from thedate of purchase. Excluded are ac
23CE Declaration of ConformityThis equipment is in compliance with the essential require-ments and other relevant provisions of Directive 89/336/EU.Th
24Book_51xxxx_1106_SP6.book Seite 24 Mittwoch, 13. Juni 2007 3:07 15
Book_51xxxx_1106_SP6.book Seite 14 Mittwoch, 13. Juni 2007 3:07 15
Sennheiser electronic GmbH & Co. KG30900 Wedemark, GermanyPhone +49 (5130) 600 0Fax +49 (5130) 600 300www.sennheiser.comPrinted in Germany
1Safety instructionsy Please read these instructions carefully andcompletely before using the headset.y Make these instructions easily accessible to a
2y Only replace those parts of the headset whosereplacement is described in this manual. All otherparts of the headset must be replaced by yourSennhei
3The HMEC 46 headsetThe HMEC 46 headset with NoiseGard™ active noise com-pensation features dynamic, open headphones. Thenoise-compensating condenser
4Delivery includesy HMEC 46 headset y Cable clip y Wind and pop screeny Instructions for usey Carry bagy EASA Form 1OperationTurning the microphone bo
5Putting on the headsetWhen putting on the headset, the patented two-pieceheadband adjusts automatically.Positioning the microphone Bend the flexible
6Flipping away one earcupThe headset features a “flip-away” earcup for single-sided listening.Adjusting the volume directly on the intercomConnect the
7Adjusting the microphone sensitivityThe microphone sensitivity has been factory pre-set to40 mV/Pa as per RTCA DO-214. You can change themicrophone s
Comments to this Manuals