Sennheiser EM 3532-U Specifications Page 18

  • Download
  • Add to my manuals
  • Print
  • Page
    / 148
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 17
EM 3031, 3032, 3532
07 / 98 - 18
8.3 EM 3031/32 TUNER-MODUL AUSTAUSCHEN
Achtung:
Während das Programmierkabel M-SePT2 PH auf der
Empfängerschnittstelle "CONFIG INPUT" gesteckt ist, nicht die
Bedienelemente "SET", "UP" und "DOWN" benutzen!
Zum A/jointfilesconvert/423974/bgleich und zur Reparatur ist das Gehäuse der Empfänger
zu demontieren.
1. Gehäuse öffnen; dazu mit Schraubendreher zwei Schrauben
(1) auf der Rückseite des Chassis lösen und entfernen.
Chassis nach vorne aus dem Gehäuse ziehen.
2. Antennenkabel (2) von Buchsen J1 und J101 des Tuner-
Moduls (3) lösen
(Achtung! Antennenstecker vorsichtig mit
Flachzange aus den Buchsen ziehen. Stecker nicht aus den
Buchsen hebeln, da Leiterplatte zerstört werden kann)
.
3. Schrauben (4) des Tuner-Moduls lösen.
4. Tuner-Modul von Hauptplatine entnehmen.
1
1
2
3
4
4
4
5. Austausch-Tuner-Modul auf Hauptplatine stecken.
6. Tuner-Modul mit Schrauben (4) befestigen.
7. Antennenkabel (2) seitenrichtig auf Tuner-Modul aufstecken
(ANT. A auf J1, ANT. B auf J101).
8a. Ist das Tuner-Modul bereits a/jointfilesconvert/423974/bgeglichen, sind lediglich die
Empfangsfrequenzen und Spezifikationen des Empfängers
zu überprüfen.
8b. Ist das
UHF-Tuner-Modul A001
ein Ersatzteil vom Sennheiser
Service, ist es auf eine Schaltbandbreite von 24 MHz in der
Mitte des bestückten HF-Teils a/jointfilesconvert/423974/bgeglichen.
Bereich Nr. 1: 430 - 494 MHz a/jointfilesconvert/423974/bgeglichen auf 450 - 474 MHz
Bereich Nr. 2: 470 - 598 MHz a/jointfilesconvert/423974/bgeglichen auf 522 - 546 MHz
Bereich Nr. 3: 574 - 702 MHz a/jointfilesconvert/423974/bgeglichen auf 626 - 650 MHz
Bereich Nr. 4: 680 - 814 MHz a/jointfilesconvert/423974/bgeglichen auf 735 - 759 MHz
Bereich Nr. 5: 798 - 960 MHz a/jointfilesconvert/423974/bgeglichen auf 867 - 891 MHz
8c. Ist das
VHF-Tuner-Modul A012
ein Ersatzteil vom Sennheiser
Service, ist es auf eine Schaltbandbreite von 7 MHz in der
Mitte des bestückten HF-Teils a/jointfilesconvert/423974/bgeglichen.
Bereich Nr. 1: 138 - 155 MHz a/jointfilesconvert/423974/bgeglichen auf 143 - 150 MHz
Bereich Nr. 2: 148 - 181 MHz a/jointfilesconvert/423974/bgeglichen auf 161 - 168 MHz
Bereich Nr. 3: 174 - 223 MHz a/jointfilesconvert/423974/bgeglichen auf 195 - 202 MHz
Bereich Nr. 4: 216 - 260 MHz a/jointfilesconvert/423974/bgeglichen auf 234 - 241 MHz
8.3 REPLACING THE EM 3031/32 TUNER ASSEMBLY
Attention:
Do not use the switches "SET", "UP", and "DOWN" on
the front panel while the programming cable M-SePT2 PH is
connected to the receiver bus "CONFIG INPUT"!
For alignment and repairs, the receivers have to be disassembled.
1. For opening the housing, unlock two screws (1) on the rear
of the chassis with a screwdriver. Pull the chassis forwards
out of the housing.
2. Disconnect the antenna cable (2) from the J1 and J101
sockets of the tuner assembly (3).
(Attention! The antenna
connector has to carefully be plugged out of the socket with
flat nose pliers. Do not lever the connector out of the
socket, as this can destroy the PCB)
.
3. Remove the screws (4) of the tuner assembly.
4. Remove the tuner assembly from the main PCB.
5. Plug the replacement tuner assembly onto the main PCB.
6. Fix the tuner assembly in place with screws (4).
7. Fit the antenna cable (2) onto the tuner assembly the right
way round (ANT.A to J1, ANT.B to J101).
8a. If the tuner assembly has already been aligned, you only
have to check receiving frequencies and receiver data.
8b.If the
UHF tuner assembly (A001)
is a spare part from
Sennheiser Service Department, it is aligned to a switching
bandwidth of 24 MHz.
Range No. 1: 430 - 494 MHz aligned to 450 - 474 MHz
Range No. 2: 470 - 598 MHz aligned to 522 - 546 MHz
Range No. 3: 574 - 702 MHz aligned to 626 - 650 MHz
Range No. 4: 680 - 814 MHz aligned to 735 - 759 MHz
Range No. 5: 798 - 960 MHz aligned to 867 - 891 MHz
8c. If the
VHF tuner assembly (A012)
is a spare part from
Sennheiser Service Department, it is aligned to a switching
bandwidth of 7 MHz.
Range No. 1: 138 - 155 MHz aligned to 143 - 150 MHz
Range No. 2: 148 - 181 MHz aligned to 161 - 168 MHz
Range No. 3: 174 - 223 MHz aligned to 195 - 202 MHz
Range No. 4: 216 - 260 MHz aligned to 234 - 241 MHz
Page view 17
1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 147 148

Comments to this Manuals

No comments