Sennheiser SER 1-3 User Manual Page 48

  • Download
  • Add to my manuals
  • Print
  • Page
    / 148
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 47
3
Sennheiser
MKH Range
RF CONDENSER
MICROPHONES
The Sennheiser condenser
microphones
in
using
RF circuitry are
market leaders in
so
far
as
their
electro- acoustical characteristics are concerned.
They
have
also distinguished themselves
by their
remarkable resistance to climatic conditions
over
many years
of
intensive use.
RF circuitry
By contrast
with
condenser
microphones with a
conventional
dc-bias, the RF circuitry
in
the
capsule of a condenser
microphone produces a
low
impedance in the actual condenser transducer
element.
The RF voltage
across
the transducer
is
only
in the order of
10
Volt
instead
of the
high dc-
bias
voltage which is
otherwise
necessary, this
voltage being generated by a
noiseless
oscillator
(8 MHz). The
high
operational
reliability of the
microphone is, attributable to the capsule
impedance.
The principle of
voltage matching
is
used
in
connecting
up both the Sennheiser condenser
microphones
and
dynamic microphones.
There
are
no
adverse
level or
frequency response
effects between
microphone
and
connected
equipment
owing to the extremely
low- impedance
circuits.
Power supply
Sennheiser offers condenser
microphones for
both standardised
powering
systems,
the audio
conductor
and phantom
powering.
Both
powering
modes
permit
the use of the same connecting
leads
as
in
the operational
dynamic studio
micro-
phones. The power can be supplied
by battery
adaptor or
mains powerpack.
The 12 V
audio
conductor or
AB
powering
offers a
simple
method for the use of battery
adaptors.
Mains powerpacks
are generally available
for the
48 V phantom technology.
In studio use the
powering
voltage is made available primarily
from
the
centralised
mixing board.
AB voltage sources
must be switched off
when
dynamic
microphones are connected up.
Normally
phantom voltage sources can
remain
switched
on
where dynamic
microphones are connected.
Sennheiser
use the
method laid down in standard
specifications for
identifying the powering
mode:
for AB
powered
microphones
the suffix
T is
used
and
for phantompowered microphones the
suffix
P
in
conjunction
with the
powering
voltage.
The MKH
110
and
MKH
101 -1 low frequency
microphones deviate
from
the
standard speci-
fication, these being
powered asymmetrically
via
special
mains
powerpack
units.
Interference protection
Sennheiser
condenser
microphones
display
very
high output
levels, which reduces the danger
of
interference
feedback by more than 20 dB by
comparison
with
dynamic
microphones.
Conse-
quently it
is not necessary to impose any specially
high
symmetrical
requirements for the connecting
leads.
The
microphones are also
provided
with
generously
proportioned
RF
filters
to prevent
RF
voltage leaking into the
microphone lead and at
the same time providing
further protection for the
microphones against
RF voltages. Consequently
such special
measures as
double screening of
the
leads
and RF -proof
fittings
are unnecessary
even
under the
most
difficult
operating conditions.
Sennheiser
condenser
microphones
for
RF
use do
not incorporate
any audio
frequency
transformers
and
are thus also
insensitive
to magnetic
inter-
ference fields.
Owing
to the extremely
lightweight diaphragms
the
microphones are
also
highly insensitive to
acceleration,
i.
e.
handling
noise. In most cases
it
is
thus possible
to use
the condenser
microphones
without
any
spring shockmounts.
Sennheiser
MKH range
The
MKH abbreviation
designates all Sennheiser
radiofrequency condenser
microphones. The
standardised
designations
for powering using
T
or
P
48 have already
been outlined
above. In
addition
the suffix
letter U denotes
a "Cannon"
plug connector.
The suffix
-3 denotes
matt-black
finish by comparison
with
the
basic finish
in
satin
nickel. The complete
Summary
will
be
found
in
the
following
listing.
SENNHEISER
MKH RANGE
MKH 406
Cardioid condenser
microphone with (T) AB powering
or
(P)
phantom
powering
49
MKH 416
Supercardioid
/lobe
condenser
microphone
for (T) AB powering
or
(P) phantom
powering
50
MKH 816 Shotgun directional
microphone with
lobe
characteristic
for (T) AB powering
or
(P) phantom
powering
51
MKH
106
Omnidirectional
condenser
microphone for (T) AB powering
or
(P)
phantom
powering
52
MKH
124
Clip
-on microphone system
with omnidirectional
characteristic
53
MKH
125
Clip
-on microphone system
with
omnidirectional
characteristic
for AB
powering
(T)
53
MKH
126
Clip
-on
microphone system
with
omnidirectional
characteristic
for phantom
powering (P)
53
MKH
110
Low-
frequency
microphone
with
omnidirectional
characteristic
and expanded
frequency
range to
1
Hz
54
MKH
110
-1
Low-
frequency
microphone with
omnidirectional
characteristic
and expanded
frequency
range to 0.1
Hz
54
Summary and
Technical
Data
56-59
Pt.
Pt.
Pt.
Pt.
Pt.
No.
Model No.
Model
No. Model
No.
Model
No.
Model
1560
MKH 406 T
1564 MKH
416 T
1568 MKH
816
T
1593 MKH
106 T
MKH
124
1561
MKH
406
T-3
1565 MKH
416 T-3
1569
MKH 816
T-3
1650 MKH
106
T-3
1562 MKH
406 T
U
1566 MKH
416 T U
1570
MKH 816
T
U
1604 MKH
106
T U
MKH
125 T
1563 MKH
406 T
U-3
1567
MKH
416 T
U-3
1571 MKH
816 T U-3
1649 MKH
106
T U-3
MKH
125 T-3
1188
MKH
406 P 48 1186
MKH
416 P 48
1190 MKH
816 P
48 1285
MKH
106 P
48
MKH125TU
1512
MKH
406
P
48-3 1510
MKH 416 P
48-3
1514 MKH
816 P
48-3 1806
MKH
106 P
48-3
MKH
125 T
U-3
1189 MKH406P48U
1187 MKH416P48U
1191
MKH816P48U
1286
MKH106P48U
1513
MKH
406 P 48
U-3
1511
MKH
416 P 48
U-3
1515
MKH
816
P 48
U-3
1807 MKH
106 P 48
U-3
MKH
126 P
48
MKH
126 P 48-3
MKH126P48U
Explanation:
MKH
126 P
48-3
Model
number
without suffix
= nickel
finish with small
Tuchel
plug connector
U =
nickel
finish with Cannon
plug -3 =
matt black
with small
Tuchel connector
plug
0372
MKH
110
U -3 =
matt-black
with Cannon
plug connector
0373
MKH
110-1
48
Page view 47
1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 147 148

Comments to this Manuals

No comments